Asphalt Calculator
This asphalt calculator turns area and compacted thickness into tons: 50 × 12 ft at 3 in takes about 11 tons[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct).
Published range 140–160 lb/ft³.
You need
11tons
- Pounds
- 22,001 lb
- Volume
- 5.56 yd³ (150 ft³)
- Area
- 600 ft²
- Spread rate
- 110 lb/yd² per in
600 square feet of hot mix asphalt at 3 in compacted needs about 11 tons.
Range at 140–160 lb/ft³: 10.5–12 tons.
Estimate only — confirm quantities with your supplier before ordering.
More options: shape, extra and price
For edges and low spots.
The calculator opens with an example size and thickness; replace them with yours. It works as a blacktop calculator and asphalt tonnage calculator for driveways, patches, paths and parking areas. Switch to Millings for recycled asphalt millings and enter the density your supplier gives you. Add a price per ton under More options to estimate the cost.
Key facts
Compacted hot mix asphalt weighs about 146[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com) pounds per cubic foot and can vary from 140 to 160[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com) pounds, according to a U.S. Navy equipment operator manual.
The Navy manual and the Kentucky Transportation Cabinet both use 110 pounds per square yard[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct) for each inch of compacted depth.
1 square yard at 1 inch thick is 0.75 cubic feet, so that spread rate is 146.7 pounds per cubic foot[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct).
Indiana DOT says loose mix is placed about ¼ inch[src] Sources: Indiana Department of Transportation thicker per inch of compacted depth.
The FHWA reports milled or processed asphalt (RAP) at 120 to 140[src] Sources: Federal Highway Administration, U.S. Department of Transportation pounds per cubic foot.
How we calculate
Formula
Volume (ft³) = area (ft²) × compacted thickness (in) ÷ 12
Tons = volume (ft³) × density (lb per ft³) ÷ 2,000
Spread rate (lb per yd² per in) = density (lb per ft³) × 0.75
Assumptions and defaults
The default hot mix density comes from the spread rate of 110 pounds per square yard per inch[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct), stated by both the Navy manual and the Kentucky Transportation Cabinet.
You can change the density to your mix design or supplier figure. The result card shows the tons across the 140 to 160[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com) pound range.
- Millings have no default density. The sources disagree, so you enter your supplier’s figure.
Thickness means compacted thickness for hot mix. The calculator starts with an example value; this site does not publish a recommended driveway thickness.
How to calculate asphalt tonnage
Asphalt tonnage is the volume of the finished mat times its density, converted to tons. Step by step:
- Measure the length and width in feet and multiply for square feet.
- Convert the compacted thickness from inches to feet by dividing by 12.
- Multiply square feet × thickness in feet to get cubic feet.
- Multiply by the density in pounds per cubic foot.
- Divide by 2,000 to get tons.
For a lot 40 feet by 60 feet at 2 inches compacted: 2,400 square feet × 0.17 feet = 400 cubic feet. At the default density that is 29.33 tons[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct).
The spread-rate shortcut
The same math can be done with a spread rate in pounds per square yard per inch. Tons = square yards × inches × spread rate ÷ 2,000. With 110 pounds[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct), a 100 square yard area at 2 inches is 11 tons[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct). Both methods give the same answer because 1 square yard at 1 inch is 0.75 cubic feet.
How much asphalt do I need?
The tonnage you need depends on the area and the compacted thickness. This table shows tons of hot mix at the default density for common sizes:
Asphalt driveway calculator
For a driveway, measure the full length, the width, and any parking or turnaround area, and add them. The thickness is a design choice that depends on your soil, base and traffic, so agree on it with your paving contractor and enter it above. As a driveway paving calculator, the tool also gives the volume in cubic yards, which helps if you are comparing with a concrete quote on the concrete calculator.
How far does a ton of asphalt go?
A ton of hot mix covers less area the thicker you lay it. At the default density, one ton covers about 82 square feet[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct) at 2 inches compacted, 55 square feet[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct) at 3 inches, and 41 square feet[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct) at 4 inches. Use this to sanity-check a quote: divide your area by the coverage per ton at your thickness, and the answer should match the calculator.
Asphalt density
Asphalt density is the weight of one cubic foot of compacted mix. A U.S. Navy equipment operator manual gives about 146[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com) pounds per cubic foot and says the figure can vary from 140 to 160[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com) pounds. It ties that figure to 110[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com) pounds per square yard per inch. The Kentucky Transportation Cabinet uses the same 110[src] Sources: Kentucky Transportation Cabinet (proposal text published on BidNet Direct) pounds per square yard per inch when it estimates asphalt quantities. The calculator uses that shared spread rate as its default.
Your paving company’s mix design is the best figure if you have it. Type it into the density field and the tons update.
Hot mix asphalt calculator: loose vs compacted
Hot mix is placed thicker than its finished depth and rolled down. The Indiana Department of Transportation says loose mix is placed about ¼ inch[src] Sources: Indiana Department of Transportation thicker for each inch of compacted depth, so a 3[src] Sources: Indiana Department of Transportation inch mat is placed about 3 ¾[src] Sources: Indiana Department of Transportation inches thick behind the paver. Always enter the compacted thickness in the calculator: tons are the same before and after rolling, only the thickness changes.
Asphalt millings calculator
Asphalt millings, also called recycled asphalt pavement or RAP, are ground-up old pavement. Switch the calculator to Millings, enter the area and depth, and enter a density.
There is no default density for millings because published figures disagree. The Federal Highway Administration reports that milled or processed RAP ranges from 120 to 140[src] Sources: Federal Highway Administration, U.S. Department of Transportation pounds per cubic foot, and gives a compacted unit weight of 100-125[src] Sources: Federal Highway Administration, U.S. Department of Transportation pounds per cubic foot. Ask your supplier for their figure. With a density of 120 pounds per cubic foot, 600 square feet at 4 inches is 12 tons.
Base and subgrade
Asphalt sits on layers below it. If your project includes a new gravel base, calculate it with the gravel base calculator. If the ground needs building up first, the fill dirt calculator covers the subgrade. Each layer is ordered separately. To calculate cubic yards for any other material, use the cubic yard calculator.
How much is asphalt per ton?
Asphalt prices vary from place to place and over time, so this site does not publish a price. Ask for a price per ton and enter it under More options. The result shows the cost of the tons you need, including any extra you added.
Worked examples
Two-car driveway. 20 feet by 40 feet at 3 inches compacted: 200 cubic feet × 146.7[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct) ÷ 2,000 = 14.67 tons[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct).
Pothole patch. A patch 4 feet by 3 feet at 2 inches needs 0.15 tons[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct), or 293 pounds[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct).
Round turnaround. A circle 30 feet across at 2 inches covers 707 square feet, which is about 8.64 tons[src] Sources: U.S. Navy Equipment Operator Basic training manual (reproduced by Integrated Publishing, tpub.com); Kentucky Transportation Cabinet (proposal text published on BidNet Direct).
Common mistakes
- Entering loose thickness. Use the compacted thickness.
- Using a density from a different mix. Densities vary; use your supplier’s if you have it.
- Forgetting edges and tapers. Add a little extra for edges, joints and low spots.
- Confusing millings with hot mix. Millings have their own, lower density.