Topsoil Calculator
This topsoil calculator gives cubic yards, tons and truckloads of topsoil for lawns, at the 4 to 6 inch[src] Sources: Penn State Extension; New Mexico State University, College of Agricultural, Consumer and Environmental Sciences depth extension guides recommend.
Extension guides call for 4–6 in for a new lawn.
For uneven ground and spills.
You need
18.52cubic yards
- Cubic feet
- 500 ft³
- Cubic meters
- 14.16 m³
- Weight (dry topsoil)
- 19.5 tons
- Tandem loads (12 yd³)
- 2
- Single-axle loads (6 yd³)
- 4
A 50 ft × 20 ft area, 6 in deep, needs 18.52 cubic yards of topsoil (500 cubic feet).
Estimate only — confirm quantities with your supplier before ordering.
More options: material, weight and price
The depth starts at 6 inches[src] Sources: Penn State Extension; New Mexico State University, College of Agricultural, Consumer and Environmental Sciences, the top of that range, so your order is not short after the soil settles.
The calculator opens with a 1,000 square foot lawn as an example; replace it with your own measurements. It works as a top soil calculator for any bulk topsoil job: new lawns, filling low spots before seeding, and spreading soil under sod. For raised beds and containers, the soil calculator is a better fit.
Key facts
Penn State Extension says a minimum of 4 to 6 inches[src] Sources: Penn State Extension of good topsoil, firmed or settled, is needed for good turf.
New Mexico State University aims for a total topsoil depth of 4–6 inches[src] Sources: New Mexico State University, College of Agricultural, Consumer and Environmental Sciences after firming.
Purdue Extension: about 19 cubic yards[src] Sources: Purdue Extension of topsoil makes a 6-inch[src] Sources: Purdue Extension layer over 1,000 square feet[src] Sources: Purdue Extension.
One cubic yard covers 54 square feet at 6 inches deep.
Dry, loose loam weighs about 2,106 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing per cubic yard.
How we calculate
Formula
Cubic yards = length (ft) × width (ft) × depth (in) ÷ 12 ÷ 27
Tons = cubic yards × weight (lb per yd³) ÷ 2,000
Assumptions and defaults
The default depth is 6 inches[src] Sources: Penn State Extension; New Mexico State University, College of Agricultural, Consumer and Environmental Sciences, the upper end of the range from Penn State and New Mexico State, so the order is not short after the soil settles.
Topsoil weight uses the figure for loam (common earth), because neither weight source lists topsoil on its own. Pick Custom density to use your supplier’s figure.
- Truckloads use the Texas Department of Transportation truck sizes and always round up.
How much topsoil do I need?
How much topsoil you need is area × depth, converted to cubic yards. Penn State Extension says that typically a minimum of 4 to 6 inches[src] Sources: Penn State Extension of topsoil, measured after it is firmed, is needed to establish good turf. Here is how to work it out:
- Measure the lawn area in feet. Split odd shapes into rectangles, circles and triangles; the cubic yard calculator explains each shape.
- Pick a depth inside the recommended range. Remember the guides mean the firmed depth.
- Multiply length × width × depth in feet and divide by 27.
- Add a margin for settling, then round up.
A back lawn 40 feet by 30 feet at 6 inches needs 22.22 cubic yards. At 4 inches it needs 14.81 cubic yards.
Topsoil for every 1,000 square feet
Purdue Extension notes that about 19 cubic yards[src] Sources: Purdue Extension of topsoil makes a 6-inch[src] Sources: Purdue Extension layer over 1,000 square feet[src] Sources: Purdue Extension. The exact figure is 18.52 cubic yards, so a round number for ordering is reasonable. This table gives cubic yards for common lawn sizes:
| Area | 2 in deep (yd³) | 4 in deep (yd³) | 6 in deep (yd³) |
|---|---|---|---|
| 10 × 50 ft (500 ft²) | 3.09 | 6.17 | 9.26 |
| 20 × 50 ft (1000 ft²) | 6.17 | 12.35 | 18.52 |
| 30 × 50 ft (1500 ft²) | 9.26 | 18.52 | 27.78 |
| 40 × 50 ft (2000 ft²) | 12.35 | 24.69 | 37.04 |
| 50 × 60 ft (3000 ft²) | 18.52 | 37.04 | 55.56 |
| 50 × 100 ft (5000 ft²) | 30.86 | 61.73 | 92.59 |
What does a yard of topsoil cover?
One cubic yard of topsoil covers less area as you go deeper. A cubic yard is 27 cubic feet, so divide by the depth in feet:
| Depth (in) | Area covered by 1 yd³ (ft²) | Cubic yards per 100 ft² (yd³) |
|---|---|---|
| 1 | 324 | 0.31 |
| 2 | 162 | 0.62 |
| 3 | 108 | 0.93 |
| 4 | 81 | 1.23 |
| 6 | 54 | 1.85 |
How far do 3 cubic yards of topsoil go?
Three cubic yards of topsoil is 81 cubic feet. That covers about 162 square feet at 6 inches, or 243 square feet at 4 inches. It weighs about 3.16 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing dry and loose, so check your vehicle’s payload before hauling it yourself.
What does 1 cubic yard of soil cover?
One cubic yard of soil covers 54 square feet at 6 inches deep and 81 square feet at 4 inches. For a thin layer to fill small dips, 1 inch deep, the same yard covers 324 square feet.
Firmed depth vs loose depth
The extension guides give the depth after the topsoil is firmed or settled. Loose soil from a truck packs down. The U.S. Army earthmoving manual lists one loose cubic yard of loam compacting to about 0.72[src] Sources: Headquarters, Department of the Army cubic yard. Light firming for a lawn is not the same as heavy compaction, so treat that as an upper bound. A practical approach is to add a margin in the extra field rather than ordering the bare minimum.
How much does topsoil weigh?
Neither of the weight sources lists topsoil by name, so this page uses the figure for loam (common earth). A cubic yard of dry, loose loam weighs about 2,106 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing, or 1.05 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.
| Material | Typical weight (lb/yd³) | Published range (lb/yd³) | Tons per yd³ (tons) |
|---|---|---|---|
| Topsoil (uses the loam / fill-dirt weight)[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 2,106 | 1,900–2,200 | 1.05 |
| Fill dirt (earth, loam or silt)[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 2,106 | 1,900–2,200 | 1.05 |
| Sand[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing | 2,700 | 2,600–2,900 | 1.35 |
Moist topsoil weighs more: the Army manual puts wet loam at 2,800 to 3,200[src] Sources: Headquarters, Department of the Army pounds per cubic yard. If your supplier sells by the ton, use the convert cubic yards to tons tool or pick tons in the price field.
Topsoil for sod, seed and leveling
- Before sod. The same 4 to 6 inch[src] Sources: Penn State Extension; New Mexico State University, College of Agricultural, Consumer and Environmental Sciences guidance applies. The sod calculator counts pieces and pallets and adds the topsoil underneath.
- Before seed. Use the same depth. Penn State suggests mixing 2 inches[src] Sources: Penn State Extension of the topsoil into the upper 2 to 3 inches[src] Sources: Penn State Extension of subsoil for a gradual transition between the two.
- Filling low spots. Measure each dip, run the calculator for each one and add them.
- Beds around the lawn. For mulch on the beds, the mulch calculator counts bags and yards.
How much is topsoil per yard?
Topsoil prices depend on your region, the screening, any compost blended in, and the delivery distance, so this site does not publish a price. Ask for the price per cubic yard and the delivery fee, enter them under More options, and the calculator shows the total. Compare a few quotes using the same volume.
Worked examples
New front lawn. A lawn 60 feet by 25 feet at 5 inches needs 23.15 cubic yards, about 24.38 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing dry. That is 2 tandem loads[src] Sources: Texas Department of Transportation; Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky) at the TxDOT size.
Round play area. A circle 20 feet across at 4 inches needs 3.88 cubic yards.
Strip along a fence. A strip 80 feet long and 3 feet wide at 6 inches needs 4.44 cubic yards.
Common mistakes
- Spreading the minimum loose. The guides mean firmed depth. Loose soil settles.
- Skipping the subsoil prep. Penn State recommends mixing some topsoil into the subsoil to avoid a sharp layer.
- Hauling it yourself without checking weight. A few yards of moist topsoil is heavy.
- Using topsoil for raised beds. Beds and containers have different needs; use the soil calculator.