Skip to content

Stone Calculator

This stone calculator gives cubic yards, tons and truckloads of river rock, landscape rock, limestone, rip rap or stone dust: a bed 20 × 6 ft at 3 in needs 1.11 cubic yards.

Area shape

Example depth. Enter the depth your project needs.

For uneven ground and spills.

You need

1.11cubic yards

Cubic feet
30 ft³
Cubic meters
0.85 m³
Weight (river rock)
1.58 tons
Tandem loads (12 yd³)
1
Single-axle loads (6 yd³)
1

A 20 ft × 6 ft area, 3 in deep, needs 1.11 cubic yards of stone (30 cubic feet).

Estimate only — confirm quantities with your supplier before ordering.

More options: stone type, weight and price

Pick the stone type under More options to label the result. Every type uses the general gravel weight for now, because no separate verified weight was found for each stone; choose Custom density to use your supplier’s figure. The calculator opens with an example; replace it with your measurements. For pea gravel, #57 stone, crusher run and road base, use the gravel calculator.

Key facts

How we calculate

Formula

Cubic yards = length (ft) × width (ft) × depth (in) ÷ 12 ÷ 27

Tons = cubic yards × weight (lb per yd³) ÷ 2,000

Assumptions and defaults

  • All stone types share the general dry gravel weight, which is Rockland’s figure for 1/4 to 2 inch gravel, inside the Army manual’s range for dry gravel.

  • Real stone products vary, so the tons figure is an estimate. A supplier’s weight per cubic yard is better; enter it as Custom density.

  • Results are loose cubic yards, the way stone is delivered.
  • The depth starts with an example. Use the depth your design or supplier calls for.
A rectangular area with length, width and depth labelledlengthwidthdepth

How much stone do I need?

The amount of stone you need is the area times the depth, converted to cubic yards, and then to tons if your supplier sells by weight.

  1. Measure the bed or border in feet. Split curves into simple shapes.
  2. Pick a depth in inches. Bigger stones need a deeper layer to hide the ground below.
  3. Multiply length × width × (depth ÷ 12) and divide by 27.
  4. Multiply by the weight per cubic yard and divide by 2,000 for tons.
  5. Add a margin and round up.

A border 40 feet long and 3 feet wide at 2 inches needs 0.74 cubic yards, about 1.05 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing at the general weight.

Stone calculator in square feet

If you already know the area in square feet, enter it as a rectangle with a width of 1 foot. A 250 square foot bed at 3 inches needs 2.31 cubic yards.

River rock calculator

River rock is calculated like any loose stone: area × depth. Pick River rock under More options to label the result. A dry creek bed 30 feet long and 4 feet wide at 4 inches needs 1.48 cubic yards. No verified weight for river rock was found, so the tons figure uses the general gravel weight. Ask your supplier for theirs, because rounded river stone and angular rock can weigh different amounts.

Landscape rock and decorative rock

Landscape rock, decorative rock and landscaping rock all mean loose stone spread in beds and borders. The calculator works the same way for each. A rock coverage calculator is just the reverse: one cubic yard covers this much at each depth.

Rock coverage per cubic yard
Depth (in)Area covered by 1 yd³ (ft²)Cubic yards per 100 ft² (yd³)
13240.31
21620.62
31080.93
4811.23
6541.85
Pure arithmetic: 27 cubic feet ÷ (depth in inches ÷ 12). Rounded to 2 decimals.

Limestone calculator

Rockland’s weights table lists broken limestone at 2,605[src] Sources: Rockland Manufacturing pounds per cubic yard, which is close to the general gravel weight of 2,835 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing the calculator uses. For crushed limestone used as a compacted base, the material will settle; see the compaction notes on the gravel calculator page.

How much does a yard of stone weigh?

Different rocks weigh different amounts per cubic yard. These figures from Rockland’s table and the Army manual show the spread:

Material (as listed) Pounds per cubic yard Source
Stone, crushed 2,700[src] Sources: Rockland Manufacturing Rockland
Limestone, lump, broken 2,605[src] Sources: Rockland Manufacturing Rockland
Granite, broken 2,781[src] Sources: Rockland Manufacturing Rockland
Sandstone, broken 2,538[src] Sources: Rockland Manufacturing Rockland
Slate, broken 2,808[src] Sources: Rockland Manufacturing Rockland
Trap rock, loose 2,700 to 3,500[src] Sources: Headquarters, Department of the Army U.S. Army FM 5-434
Gravel, dry (used by this calculator) 2,835[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing Rockland, inside the Army range

These are reference figures, not a promise about any one product. To convert any volume to tons, use the convert cubic yards to tons tool.

Stone calculator in tons

At the general gravel weight, one cubic yard of stone is about 1.42 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing and one ton is about 0.71 cubic yards[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.

Tons of stone at the general gravel weight
Volume (yd³)Gravel (tons)
0.5[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing0.71
11.42
22.84
34.25
45.67
57.09
811.34
1014.18
Cubic yards × typical weight (lb/yd³) ÷ 2,000. Dry, loose material; rounded to 2 decimals.

How far does a ton of stone go?

At the general gravel weight, one ton of stone covers about 114 square feet[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing at 2 inches deep, 76 square feet[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing at 3 inches, and 57 square feet[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing at 4 inches. Heavier rock covers less per ton and lighter rock covers more, so use these as a check rather than an order quantity.

Crushed limestone calculator

Crushed limestone is calculated like any stone. For a path 50 feet by 4 feet at 3 inches, you need 1.85 cubic yards. At Rockland’s figure for broken limestone, 2,605[src] Sources: Rockland Manufacturing pounds per cubic yard, pick Custom density and enter it to see the tons. If you compact the limestone, it settles; the Army manual’s factor for sand or gravel is 0.86[src] Sources: Headquarters, Department of the Army compacted yard per loose yard.

Rip rap calculator

Rip rap is large, angular rock placed on slopes and channels to resist erosion. The calculator gives the volume of the layer: enter the area of the slope and the thickness of the rock layer. Rock size changes how much weight fits in a cubic yard, so ask your supplier or engineer how they convert volume to tons for your rock size. A slope 30 feet long and 10 feet wide with a 18 inch layer holds 16.67 cubic yards.

Stone dust calculator

Stone dust is fine crushed rock. Enter the area and the depth of the layer. A 12 × 12 foot area at 1 inch needs 0.44 cubic yards. It compacts when tamped, so add a margin. The Army manual’s factor for sand or gravel is 0.86[src] Sources: Headquarters, Department of the Army compacted yard per loose yard.

Worked examples

Front bed with river rock. 25 feet by 5 feet at 3 inches: 31.25 cubic feet = 1.16 cubic yards.

Round tree bed with landscape rock. A circle 8 feet across at 2 inches: 0.31 cubic yards.

Large job. 20 cubic yards of stone is 2 tandem loads[src] Sources: Texas Department of Transportation; Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky) at the TxDOT truck size.

Common mistakes

For anything round, triangular or irregular, the cubic yard calculator explains each shape. A sand layer under stone? Use the sand calculator.

Frequently asked questions

How much stone do I need?

Multiply length × width × depth in feet and divide by 27 for cubic yards. A bed 20 feet by 6 feet at 3 inches deep needs 1.11 cubic yards of stone, about 1.58 tons at the general gravel weight.

How many tons of river rock do I need?

Work out the cubic yards, then multiply by the weight per cubic yard and divide by 2,000. This site uses the general gravel weight of 2,835 pounds per cubic yard for river rock, because no verified river rock figure was found. Enter your supplier's weight for a better answer.

How much does a yard of landscape rock weigh?

It depends on the rock. Rockland's weights table lists crushed stone at 2,700 pounds per cubic yard, broken limestone at 2,605 and broken granite at 2,781.

How much area does a ton of stone cover?

At the general gravel weight, one ton is about 0.71 cubic yards, which covers about 76 square feet at 3 inches deep.

How do I calculate rip rap?

Measure the area of the slope or channel and the thickness of the rock layer, and use the calculator for cubic yards. Rip rap is large rock with big gaps, so ask your supplier or engineer how they convert that volume to tons for the size you order.

Is stone the same as gravel on this site?

The math is the same. This page covers landscape stone such as river rock, limestone, rip rap and stone dust. Pea gravel, #57 stone, crusher run and road base are on the gravel calculator.

Sources and references

  1. Headquarters, Department of the Army. FM 5-434 Earthmoving Operations, Table 1-2. Material Weight, Swell Percentages, and Load Factors. vulcanhammer.net/wp-content/uploads/2017/01/fm5_434.pdf. Accessed November 11, 2026.
  2. Rockland Manufacturing. Weights of Materials. rocksi.rocklandmfg.com/desktop/assets/Rockland-Weights-of-Materials.pdf. Accessed November 11, 2026.
  3. Texas Department of Transportation. Seal Coat and Surface Treatment Manual, Section 5: Haul Trucks — Size. www.txdot.gov/manuals/mnt/scm/equipment_inspection/haul_trucks-i1008556/size-i1008586.html. Accessed November 11, 2026.
  4. Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky). Dump Truck | Highway Knowledge Portal. kykp.gov/knowledge-portal/articles/truck-dump/. Accessed November 11, 2026.

Update history

  • — First published.