Skip to content

Gravel Calculator

This gravel calculator gives cubic yards, tons and truckloads: 50 × 10 ft at 4 in is 6.17 cubic yards, about 8.75 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.

Area shape

Example depth. Enter the depth your project needs.

For uneven ground and spills.

You need

6.17cubic yards

Cubic feet
166.67 ft³
Cubic meters
4.72 m³
Weight (dry gravel)
8.75 tons
Tandem loads (12 yd³)
1
Single-axle loads (6 yd³)
2

A 50 ft × 10 ft area, 4 in deep, needs 6.17 cubic yards of gravel (166.67 cubic feet).

Estimate only — confirm quantities with your supplier before ordering.

More options: gravel type, weight and price

The calculator opens with an example; replace it with your measurements. Pick the gravel type under More options to label your result. Pea gravel, #57 stone, 3/4 in. crushed stone, crusher run and road base all use the general gravel weight, because no separate verified weight was found for each one. If your supplier gives a weight per cubic yard, choose Custom density. For river rock, limestone and other landscape stone, use the stone calculator.

Key facts

How we calculate

Formula

Cubic yards = length (ft) × width (ft) × depth (in) ÷ 12 ÷ 27

Tons = cubic yards × weight (lb per yd³) ÷ 2,000

Cubic yards from tons = tons × 2,000 ÷ weight (lb per yd³)

Assumptions and defaults

  • The gravel weight is Rockland’s figure for dry gravel between 1/4 and 2 in., used because it sits inside the Army manual’s range for dry gravel.

  • Every gravel type uses that same weight until a verified weight for each type is available. Custom density overrides it.

  • Results are loose cubic yards, the way gravel is delivered.
  • The depth field starts with an example value. This site does not publish a recommended driveway depth (see below).

A rectangular area with length, width and depth labelledlengthwidthdepth

How much gravel do I need?

The amount of gravel you need is the area times the depth, converted to cubic yards, and then to tons if your supplier sells by weight.

  1. Measure the length and width in feet. Split curved or odd shapes into simple ones.
  2. Decide on the finished depth. Measure in inches.
  3. Multiply length × width × (depth ÷ 12) and divide by 27 for cubic yards.
  4. Multiply cubic yards by the gravel weight and divide by 2,000 for tons.
  5. Add a margin for compaction and edges, then round up.

For a parking pad 20 feet by 20 feet at 4 inches: 133.33 cubic feet = 4.94 cubic yards = about 7 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.

Gravel calculator in tons

Some suppliers price gravel by the ton and others by the cubic yard, so the calculator shows both. The math uses 1.42 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing per cubic yard of dry gravel. Use this table to check an order:

Tons of dry gravel for common volumes
Volume (yd³)Gravel (tons)
1[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing1.42
22.84
34.25
45.67
57.09
68.51
811.34
1014.18
1217.01
1419.85
2028.35
Cubic yards × typical weight (lb/yd³) ÷ 2,000. Dry, loose material; rounded to 2 decimals.

How many yards in a ton of gravel?

One ton of dry gravel is about 0.71 cubic yards[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing. Ten tons is about 7.05 cubic yards[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing. If your gravel is wet, each yard weighs more, so a ton covers less. The Army manual lists wet gravel at 2,800 to 3,100[src] Sources: Headquarters, Department of the Army pounds per cubic yard. For other materials, use the convert cubic yards to tons tool.

Gravel coverage: how far does a yard go?

Gravel coverage depends only on depth. A cubic yard is 27 cubic feet, so at 2 inches it spreads over 162 square feet and at 4 inches over 81 square feet.

Gravel coverage per cubic yard
Depth (in)Area covered by 1 yd³ (ft²)Cubic yards per 100 ft² (yd³)
13240.31
21620.62
31080.93
4811.23
6541.85
Pure arithmetic: 27 cubic feet ÷ (depth in inches ÷ 12). Rounded to 2 decimals.

For round or triangular areas, the cubic yard calculator explains each shape formula.

Gravel driveway calculator

To estimate a driveway, measure the full length and the width you want to cover, including any turnaround. A driveway 80 feet by 10 feet at 4 inches needs 9.88 cubic yards, about 14 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing. That is 1 tandem loads[src] Sources: Texas Department of Transportation; Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky) at the TxDOT truck size.

How deep should driveway gravel be?

This site does not publish a recommended depth for gravel driveways. In the research for this page, no government, university or industry standard for residential gravel driveways was found; only seller guides, which disagree. Driveway depth depends on your soil, drainage, climate and traffic. Check your county or town driveway rules, or ask a local supplier or contractor, then enter that depth above.

For paver driveways, the paver calculator uses published base thickness guidance from the paving industry.

Gravel types: pea gravel, #57, crusher run and road base

The calculator lets you label the result by type: pea gravel, #57 stone, 3/4 in. crushed stone, crusher run or road base. All of these use the general gravel weight of 2,835 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing per cubic yard for now, so the tons figure is an estimate and your supplier’s weight is better.

Different stone products can weigh noticeably different amounts. For comparison, Rockland’s weights table lists crushed stone at 2,700[src] Sources: Rockland Manufacturing pounds per cubic yard, loose dry gravel at 2,565[src] Sources: Rockland Manufacturing, and natural gravel with sand at 3,240[src] Sources: Rockland Manufacturing. That spread is why the calculator lets you enter a custom density.

How much pea gravel do I need?

Pea gravel is calculated the same way as any gravel. A play area 12 feet by 12 feet at 3 inches needs 1.33 cubic yards. Pick Pea gravel in the type list to label the result.

Crusher run and road base calculator

If you compact crusher run or road base, it takes up less room than it did in the truck. The Army manual says one loose cubic yard of sand or gravel compacts to about 0.86[src] Sources: Headquarters, Department of the Army cubic yard, so for 10 cubic yards compacted, order about 11.63 cubic yards[src] Sources: Headquarters, Department of the Army loose.

Loose vs compacted gravel

How volume changes: in the ground, loose in the truck, and compacted
Material1 yd³ in the ground → loose (yd³)1 loose yd³ → compacted (yd³)1 loose yd³ → in-ground (yd³)
Sand or gravel[src] Sources: Headquarters, Department of the Army1.110.860.9
Loam (common earth)[src] Sources: Headquarters, Department of the Army1.250.720.8
Clay[src] Sources: Headquarters, Department of the Army1.430.630.7
Factors from U.S. Army FM 5-434, Table 1-1. They are averages; grain size and moisture change them.

The factor for sand or gravel is an average, and the Army manual notes that grain size and moisture change it. Add a margin in the extra field instead of ordering the bare minimum.

How much rock do I need for drainage?

For a French drain or drainage trench, calculate the trench as a box and subtract the pipe if it is large. A trench 50 feet long, 1 foot wide and 18 inches deep holds 2.78 cubic yards of rock before subtracting the pipe. For decorative rock beds, the stone calculator covers river rock and landscape stone, and the sand calculator covers sand layers.

Gravel under asphalt

If you are paving over a gravel base, run the base through this calculator first, then use the asphalt calculator for the paving tons.

Gravel prices

Gravel prices vary by type, region and delivery distance, so this calculator never assumes a price. Enter your supplier’s price per ton or per cubic yard under More options to compare quotes. For dated price ranges by type, see gravel cost per ton.

Common mistakes

Frequently asked questions

How much gravel do I need?

Multiply length × width × depth in feet and divide by 27 for cubic yards. A path 50 feet long and 10 feet wide at 4 inches deep needs 6.17 cubic yards, which is about 8.75 tons of dry gravel.

How many yards are in a ton of gravel?

About 0.71 cubic yards of dry, loose gravel, using a weight of 2,835 pounds per cubic yard. The U.S. Army manual range for dry gravel is 2,700 to 3,000 pounds, so a ton can be a little more or less.

How much gravel do I need for my driveway?

Measure the length and width of the driveway, choose the depth you plan to lay, and enter them above. For a driveway 60 feet by 12 feet at 4 inches, that is 8.89 cubic yards, or about 12.6 tons. Check local rules or ask your supplier about the depth for your soil and traffic.

How much pea gravel do I need?

Use the same formula. A play area 12 feet by 12 feet at 3 inches deep needs 1.33 cubic yards of pea gravel. This site uses the general gravel weight for pea gravel because no separate verified figure was found.

How much does a yard of gravel weigh?

A cubic yard of dry, loose gravel weighs about 2,835 pounds, or 1.42 tons. Wet gravel is heavier: the Army manual lists it at 2,800 to 3,100 pounds per cubic yard.

How many tons of gravel fit in a dump truck?

The Texas Department of Transportation says tandem-axle trucks usually hold 12 or 14 cubic yards. At the typical dry gravel weight, 12 cubic yards is about 17.01 tons. Ask your supplier how much they carry per trip.

Sources and references

  1. Headquarters, Department of the Army. FM 5-434 Earthmoving Operations, Table 1-2. Material Weight, Swell Percentages, and Load Factors. vulcanhammer.net/wp-content/uploads/2017/01/fm5_434.pdf. Accessed November 11, 2026.
  2. Rockland Manufacturing. Weights of Materials. rocksi.rocklandmfg.com/desktop/assets/Rockland-Weights-of-Materials.pdf. Accessed November 11, 2026.
  3. Texas Department of Transportation. Seal Coat and Surface Treatment Manual, Section 5: Haul Trucks — Size. www.txdot.gov/manuals/mnt/scm/equipment_inspection/haul_trucks-i1008556/size-i1008586.html. Accessed November 11, 2026.
  4. Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky). Dump Truck | Highway Knowledge Portal. kykp.gov/knowledge-portal/articles/truck-dump/. Accessed November 11, 2026.

Update history

  • — First published.