Skip to content

Sand Calculator

This sand calculator gives cubic yards, tons, truckloads and bag counts of sand: a sandbox 6 × 6 ft at 12 in needs 1.33 cubic yards.

Area shape

Example depth. Enter the depth you need.

For uneven ground and spills.

You need

1.33cubic yards

Cubic feet
36 ft³
Cubic meters
1.02 m³
Weight (dry sand)
1.8 tons
Tandem loads (12 yd³)
1
Single-axle loads (6 yd³)
1

A 6 ft × 6 ft area, 12 in deep, needs 1.33 cubic yards of sand (36 cubic feet).

Estimate only — confirm quantities with your supplier before ordering.

More options: bags and price

The weight printed on the bag.

Use it as a paver sand calculator, fill sand calculator or play sand calculator. The calculator opens with an example; replace it with your sizes. To count bags, enter the bag weight from the label (such as 50 lb) under More options: the calculator works out the bag volume from the sand weight. For a different sand, pick Custom density and enter your supplier’s weight per cubic yard.

Key facts

How we calculate

Formula

Cubic yards = length (ft) × width (ft) × depth (in) ÷ 12 ÷ 27

Tons = cubic yards × weight (lb per yd³) ÷ 2,000

Bag volume (ft³) = bag weight (lb) ÷ (weight per yd³ ÷ 27)

Assumptions and defaults

  • The sand weight is Rockland’s figure for dry sand, which falls inside the Army manual’s range.
  • Bags sold by weight are converted to volume with that same weight. Damp bagged sand is heavier, so the bag holds a little less volume than the figure shown.

  • Truck sizes come from the Texas Department of Transportation; truckloads round up.
  • The depth starts with an example value.
A rectangular area with length, width and depth labelledlengthwidthdepth

How much sand do I need?

The amount of sand you need is area × depth, converted to cubic yards, tons or bags.

  1. Measure the length and width in feet.
  2. Decide the depth in inches.
  3. Multiply length × width × (depth ÷ 12) for cubic feet.
  4. Divide by 27 for cubic yards, or by the bag volume for bags.
  5. Add extra for compaction and spills, then round up.

For a play area 10 feet by 8 feet at 9 inches: 60 cubic feet = 2.22 cubic yards = about 3 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing of dry sand.

How many 50 lb bags of sand do I need?

A 50 lb bag of dry sand holds about 0.5 cubic feet[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing: 50 pounds divided by 100 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing per cubic foot. So one cubic yard is about 54 bags[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.

Project Sand needed 50 lb bags
Sandbox 4 × 4 ft, 8 in deep 10.67 ft³ 22[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing
Sandbox 6 × 6 ft, 12 in deep 36 ft³ 72[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing
Paver patio 12 × 12 ft, 1 in bedding 12 ft³ 24[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing
Walkway 30 × 3 ft, 1 in bedding 7.5 ft³ 15[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing

Bags in the table assume dry sand at 2,700 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing per cubic yard. If your bags list a volume instead of a weight, divide the cubic feet you need by that volume.

Paver sand calculator

Pavers sit on a thin layer of bedding sand over a compacted base. The Concrete Masonry & Hardscapes Association says bedding sand should be spread and screeded to an uncompacted nominal 1 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) thickness, and Belgard’s installation notes also call for screeding to 1-in[src] Sources: Belgard thickness. CMHA adds that bedding sands should conform to ASTM C33 or CSA A23.1 FA1 gradations, which is a concrete sand grading.

For a patio 12 feet by 16 feet, a 1 inch layer is 0.59 cubic yards. The paver calculator will add the base gravel and the paver count in one place; for now, use this calculator for the sand and the gravel calculator for the base.

Fill sand calculator

Fill sand is used to raise or level an area. It is calculated the same way, and it compacts when you tamp or roll it. The Army manual says one loose cubic yard of sand or gravel compacts to about 0.86[src] Sources: Headquarters, Department of the Army cubic yard, so for 5 cubic yards compacted, order about 5.81 cubic yards[src] Sources: Headquarters, Department of the Army loose.

Play sand calculator

For a sandbox, measure the inside of the box and decide how deep to fill it. A round sandbox 6 feet across at 10 inches holds 23.56 cubic feet, or 48 bags[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing of 50 lb. If you buy play sand in bags, use the bag weight option to count them.

How much does a yard of sand weigh?

A cubic yard of dry, loose sand weighs about 2,700 pounds[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing, which is 1.35 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing. Moisture makes it heavier.

Weight of a cubic yard of sand compared with gravel and dirt (dry, loose)
MaterialTypical weight (lb/yd³)Published range (lb/yd³)Tons per yd³ (tons)
Sand[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing2,7002,600–2,9001.35
Gravel[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing2,8352,700–3,0001.42
Fill dirt (earth, loam or silt)[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing2,1061,900–2,2001.05
Typical weight is the Rockland figure where it falls inside the U.S. Army FM 5-434 range. Moisture and compaction raise the weight. Tons are short tons of 2,000 lb.

Rockland lists wet sand at 3,240[src] Sources: Rockland Manufacturing pounds per cubic yard, and the Army manual gives 2,800 to 3,100[src] Sources: Headquarters, Department of the Army. To turn any volume into tons, use the convert cubic yards to tons tool.

Sand and gravel calculator

For a sand and gravel mix, use the calculator for the volume and pick Custom density for the weight. Rockland lists natural gravel with sand at 3,240[src] Sources: Rockland Manufacturing pounds per cubic yard; your supplier’s figure for the exact mix is better. For gravel alone, use the gravel calculator; for river rock and landscape stone, the stone calculator.

Truckloads of sand

For big jobs, the calculator counts truckloads. The Texas Department of Transportation says single-axle trucks normally carry 6 cubic yards[src] Sources: Texas Department of Transportation of aggregate and tandem-axle trucks usually hold 12 or 14 cubic yards[src] Sources: Texas Department of Transportation. 10 cubic yards of sand is 2 single-axle loads[src] Sources: Texas Department of Transportation; Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky) or 1 tandem load[src] Sources: Texas Department of Transportation; Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky).

How far does a yard of sand go?

One cubic yard of sand covers less area the deeper you spread it. A cubic yard is 27 cubic feet, so divide by the depth in feet:

Area one cubic yard of sand covers
Depth (in)Area covered by 1 yd³ (ft²)Cubic yards per 100 ft² (yd³)
13240.31
21620.62
31080.93
4811.23
6541.85
12273.7
Pure arithmetic: 27 cubic feet ÷ (depth in inches ÷ 12). Rounded to 2 decimals.

At 1 inch, the bedding depth under pavers, one yard covers 324 square feet. At 12 inches, a typical sandbox fill, it covers only 27 square feet.

Loose vs compacted sand

Sand settles when it is tamped, rolled or soaked. The U.S. Army earthmoving manual gives these average factors for sand or gravel, along with loam and clay for comparison:

How volume changes: in the ground, loose in the truck, and compacted
Material1 yd³ in the ground → loose (yd³)1 loose yd³ → compacted (yd³)1 loose yd³ → in-ground (yd³)
Sand or gravel[src] Sources: Headquarters, Department of the Army1.110.860.9
Loam (common earth)[src] Sources: Headquarters, Department of the Army1.250.720.8
Clay[src] Sources: Headquarters, Department of the Army1.430.630.7
Factors from U.S. Army FM 5-434, Table 1-1. They are averages; grain size and moisture change them.

For a compacted sand layer, order loose sand by dividing the compacted volume by 0.86[src] Sources: Headquarters, Department of the Army. Bedding sand under pavers is the exception: CMHA gives its 1 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) as an uncompacted, screeded thickness.

Worked examples

Backyard sandbox. A box 8 feet by 6 feet filled 10 inches deep: 40 cubic feet = 1.48 cubic yards, about 2 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing, or 80 bags[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing of 50 lb.

Paver patio bedding. A patio 16 feet by 20 feet with 1 inch of bedding sand: 26.67 cubic feet = 0.99 cubic yards.

Leveling with fill sand. An area 30 feet by 20 feet raised 3 inches after compaction: 5.56 cubic yards compacted, so order about 6.46 cubic yards[src] Sources: Headquarters, Department of the Army loose.

Common mistakes

For other shapes, the cubic yard calculator explains each formula.

Frequently asked questions

How much sand do I need?

Multiply length × width × depth in feet and divide by 27. A sandbox 6 feet square filled 12 inches deep needs 1.33 cubic yards of sand, which weighs about 1.8 tons dry.

How many 50 lb bags of sand do I need?

A 50 lb bag of dry sand holds about 0.5 cubic feet, using a dry sand weight of 2,700 pounds per cubic yard. The 6 foot square sandbox above takes 72 bags.

How much does a yard of sand weigh?

A cubic yard of dry, loose sand weighs about 2,700 pounds, or 1.35 tons. The U.S. Army manual lists dry sand at 2,600 to 2,900 pounds and wet sand at 2,800 to 3,100 pounds per cubic yard.

How much sand do I need under pavers?

Industry guidance calls for a bedding layer about 1 in. thick. For a 12 foot by 12 foot patio that is 0.44 cubic yards of bedding sand.

How many yards of sand are in a ton?

About 0.74 cubic yards of dry, loose sand. Wet sand is heavier per yard, so a ton covers less.

Can I use this as a sand and gravel calculator?

Yes for volume. For weight, pick Custom density and enter your supplier's figure for the mix, or use the gravel calculator for gravel alone.

Sources and references

  1. Headquarters, Department of the Army. FM 5-434 Earthmoving Operations, Table 1-2. Material Weight, Swell Percentages, and Load Factors. vulcanhammer.net/wp-content/uploads/2017/01/fm5_434.pdf. Accessed November 11, 2026.
  2. Rockland Manufacturing. Weights of Materials. rocksi.rocklandmfg.com/desktop/assets/Rockland-Weights-of-Materials.pdf. Accessed November 11, 2026.
  3. Concrete Masonry & Hardscapes Association (CMHA). Tech Note PAV-TEC-002-22: Construction of Interlocking Concrete Pavements. rochestercp.com/resources/cmha-tech-notes/PAV-TEC-002-22.pdf. Accessed November 11, 2026.
  4. Belgard. Technical Resource Guide (BEL25-D-516650), page 27. static.getfastr.com/62ebb7352a22915f359dbbe2/bfceb77e-cdc9-81e1-8008-3b1640917aaf/files/dd67896c-a5bc-81d4-8008-3b49e3a90466/seo/variants/dd67896c-a5bc-81d4-8008-3b4a371a345c/pages/27.html. Accessed November 11, 2026.
  5. Texas Department of Transportation. Seal Coat and Surface Treatment Manual, Section 5: Haul Trucks — Size. www.txdot.gov/manuals/mnt/scm/equipment_inspection/haul_trucks-i1008556/size-i1008586.html. Accessed November 11, 2026.
  6. Kentucky Transportation Cabinet Highway Knowledge Portal (Kentucky Transportation Center, University of Kentucky). Dump Truck | Highway Knowledge Portal. kykp.gov/knowledge-portal/articles/truck-dump/. Accessed November 11, 2026.

Update history

  • — First published.