Skip to content

Paver Calculator

This paver calculator gives the paver count, base gravel and bedding sand for a patio, walkway or driveway: a 12 × 12 ft patio of 4 × 8 in pavers takes 648 pavers.

Enter size as

You need

648pavers

Paved area
144 ft²
Base gravel (6 in)
2.67 yd³ · 3.78 tons
Bedding sand (1 in)
0.44 yd³ · 0.6 tons

144 square feet of 8 × 4 in pavers needs 648 pavers, 2.67 cubic yards of base and 0.44 cubic yards of bedding sand.

Estimate only — confirm quantities with your supplier before ordering.

More options: base, extra, sand and price

For cuts and breakage.

Each side. Belgard: 6–8 in.

The paver size starts as an example; enter the size of your paver. The base depth comes from paving industry guidance for patios or driveways, and the bedding sand starts at 1 inch[src] Sources: Concrete Masonry & Hardscapes Association (CMHA); Belgard. It works as a paver base calculator and paver gravel calculator too: the result shows the base in cubic yards and tons.

Key facts

How we calculate

Formula

Pavers = area (ft²) × (1 + extra %) ÷ (paver length × width ÷ 144), rounded up

Base (yd³) = base area × base depth (in) ÷ 12 ÷ 27

Bedding sand (yd³) = area × sand depth (in) ÷ 12 ÷ 27

Tons = cubic yards × weight (lb per yd³) ÷ 2,000

Assumptions and defaults

A rectangular area with length, width and depth labelledlengthwidthdepth

How many pavers do I need?

To count pavers, divide the area by the area of one paver, then add extra for cuts and breakage.

  1. Measure the length and width in feet, or add up the areas of each section.
  2. Measure one paver in inches. Multiply length × width and divide by 144 for square feet per paver.
  3. Divide the area by the square feet per paver.
  4. Add extra for cuts, especially for curves, borders and patterns, and round up.

A walkway 30 feet by 4 feet is 120 square feet. With 6 × 9 inch pavers (0.375 square feet each), that is 320 pavers, or 352 pavers with 10 % extra.

Pavers per square foot

Different paver sizes need very different counts. This table assumes no extra:

Paver size Square feet each Pavers per square foot Pavers for 100 ft²
4 × 8 in 0.222 4.5 450
6 × 6 in 0.25 4 400
6 × 9 in 0.375 2.67 267
12 × 12 in 1 1 100
12 × 24 in 2 0.5 50

If your paver maker lists coverage for a pattern that mixes sizes, use their figure.

Paver base calculator

The base is the compacted gravel layer under the sand and pavers. How thick it should be depends on traffic and soil:

Use CMHA minimum (well-drained soil) Unilock guide
Patios and walkways 4 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) 6” - 8”[src] Sources: Unilock
Pool decks Not listed 6” - 12”[src] Sources: Unilock
Residential driveways 6 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) 10” - 14”[src] Sources: Unilock

CMHA’s figures are minimums for well-drained soil. The calculator starts at the smallest depth that meets both sources, and you can enter more under Custom depth.

How much paver base gravel do I need?

Base volume is the base area times the base depth. For a 12 foot square patio on a 6 inch base, that is 2.67 cubic yards, about 3.78 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing. If you extend the base 6 inches past each edge, the base area becomes 13 × 13 feet, and the base grows to 3.13 cubic yards.

Unilock’s guide says to use 3/4”[src] Sources: Unilock crusher run gravel or 3/4”[src] Sources: Unilock clear stone for the base. To price the base by itself, use the paver base gravel numbers from the gravel calculator.

Compacting the base

Compacted base takes up less room than loose gravel. The Army manual says one loose cubic yard of sand or gravel compacts to about 0.86[src] Sources: Headquarters, Department of the Army cubic yard, so order more loose base than the compacted volume. Unilock’s guide compacts the base in layers 2” - 3”[src] Sources: Unilock thick with a plate compactor, and its DIY steps say to compact in layers of 3″ – 4″[src] Sources: Unilock.

Bedding sand under pavers

The bedding layer is a thin, even bed of sand the pavers sit in. CMHA says to spread and screed it to a nominal 1 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) thickness, uncompacted, and that bedding sands should conform to ASTM C33 or CSA A23.1 FA1 gradations. Belgard’s installation notes also say to screed to 1-in[src] Sources: Belgard.

For a 12 foot square patio, 1 inch of bedding sand is 0.44 cubic yards, about 0.6 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing. For bags of paver sand, the sand calculator converts bag weight to volume.

Paver layers from top to bottom

A sand-set paver surface is built in layers, and the calculator covers each one:

  1. Pavers, counted from the area and paver size, plus extra for cuts.
  2. Bedding sand, a thin screeded layer about 1 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) thick that the pavers sit in.
  3. Base, compacted crushed gravel at least 4 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) for patios and 6 in.[src] Sources: Concrete Masonry & Hardscapes Association (CMHA) for driveways on well-drained soil, according to CMHA.
  4. Subgrade, the native soil underneath, which you dig down to and compact. If it needs building up first, the dirt calculator covers fill.

Add the layer thicknesses together to know how deep to dig: for a patio with a 6 inch base, 1 inch of sand and pavers that are 2.38 inches thick, you dig about 9.375 inches below finished grade.

Base and bedding sand for common patio sizes

Patio Area Base at 6 in[src] Sources: Concrete Masonry & Hardscapes Association (CMHA); Unilock Bedding sand at 1 in[src] Sources: Concrete Masonry & Hardscapes Association (CMHA); Belgard
10 × 10 ft 100 ft² 1.85 yd³ 0.31 yd³
12 × 16 ft 192 ft² 3.56 yd³ 0.59 yd³
16 × 20 ft 320 ft² 5.93 yd³ 0.99 yd³
20 × 20 ft 400 ft² 7.41 yd³ 1.23 yd³
20 × 30 ft 600 ft² 11.11 yd³ 1.85 yd³

These are compacted base volumes with no base extended past the edge. Add your overbuild and a margin for compaction before ordering.

Worked examples

Back patio. 16 feet by 20 feet with 6 × 9 in pavers and 10 % extra: 939 pavers, a 6 inch base of 5.93 cubic yards and 0.99 cubic yards of bedding sand.

Paver driveway. 20 feet by 24 feet on a 10 inch base: 14.81 cubic yards of base, about 21 tons[src] Sources: Headquarters, Department of the Army; Rockland Manufacturing.

Garden path. 40 feet by 3 feet with 4 × 8 in pavers: 540 pavers before extra.

Common mistakes

For the area of odd shapes, the square yard calculator handles circles and triangles, and the cubic yard calculator explains the volume formulas.

Frequently asked questions

How many pavers do I need?

Divide the area by the area of one paver and add extra for cuts. A patio 12 feet square is 144 square feet. With pavers 4 inches by 8 inches, that is 648 pavers, or 713 with 10 % extra.

How thick should the base under pavers be?

The Concrete Masonry & Hardscapes Association says patios and walkways need a compacted base of at least 4 in. on well-drained soil, and residential driveways at least 6 in. Unilock's guide lists 6" - 8" for patios and walkways and 10" - 14" for driveways.

How much sand do I need under pavers?

Bedding sand is screeded to a nominal 1 in. layer. For a 12 foot square patio that is 0.44 cubic yards, about 0.6 tons of dry sand.

How much paver base gravel do I need?

Multiply the base area by the base depth. A 12 foot square patio on a 6 inch base needs 2.67 cubic yards of base, about 3.78 tons at the general gravel weight. Belgard's details extend the base 6 to 8 inches past the paver edge, which adds more.

What gravel is used for paver base?

Unilock's guide says to use 3/4" crusher run gravel or 3/4" clear stone for the base. Follow your paver maker's guide for your product.

How thick should each base layer be when compacting?

Unilock's guide compacts the base in layers 2" - 3" thick, and its DIY steps say to compact in layers of 3″ – 4″.

How many pavers are in a square foot?

Divide 144 square inches by the area of one paver. Pavers 4 by 8 inches work out to 4.5 per square foot, and pavers 12 by 12 inches to 1.

Sources and references

  1. Concrete Masonry & Hardscapes Association (CMHA). Tech Note PAV-TEC-002-22: Construction of Interlocking Concrete Pavements. rochestercp.com/resources/cmha-tech-notes/PAV-TEC-002-22.pdf. Accessed November 11, 2026.
  2. Unilock. Project Planning Guide — Understanding Paver Installation (Basic Tech Guide). unilock.com/wp-content/uploads/2024/01/Basic-Tech-Guide-update-002.pdf. Accessed November 11, 2026.
  3. Unilock. Do's and Don'ts of Paver Installation: Step 2 of 3 - Base Preparation. unilock.com/diy/dos-and-donts-of-paver-installation-base-preparation-23/. Accessed November 12, 2026.
  4. Belgard. Technical Resource Guide (BEL25-D-516650), page 27. static.getfastr.com/62ebb7352a22915f359dbbe2/bfceb77e-cdc9-81e1-8008-3b1640917aaf/files/dd67896c-a5bc-81d4-8008-3b49e3a90466/seo/variants/dd67896c-a5bc-81d4-8008-3b4a371a345c/pages/27.html. Accessed November 11, 2026.
  5. Headquarters, Department of the Army. FM 5-434 Earthmoving Operations, Table 1-2. Material Weight, Swell Percentages, and Load Factors. vulcanhammer.net/wp-content/uploads/2017/01/fm5_434.pdf. Accessed November 11, 2026.
  6. Rockland Manufacturing. Weights of Materials. rocksi.rocklandmfg.com/desktop/assets/Rockland-Weights-of-Materials.pdf. Accessed November 11, 2026.

Update history

  • — First published.